T Series Auger Features Hover over any of the images below to view the features

T Series Grain Auger T Series Auger Tires T Series Auger Top Drive Spout T Series Grain Auger Hitch Sealed Drive Shaft Bearings Long service life greasable, lower intake bushing assembly T Series Auger Gearbox T Series Auger Winch Iron Edge Flighting Electric Motor Mount T Series Hopper T Series Wheel Kit
 

Other Features:

  • Our in house engineer and designer also farms, he designed this auger with features that he wanted to see for his own farming operation. Designed by a farmer, built for a farmer.
  • Auger tubing is constructed with 14 gauge steel.
  • Non-separable PTO shaft for safety and extended lub cross kits, 50 hour lube interval. Overload protection is located above the gearbox in the upper drive shaft.
  • Powder Coat PlusTM, a special powder coating formula that gives you that quality finish you look for in equipment. Long lasting, tough and more durable than standard wet paint.
  • Iron Edge PlusTM Flighting - Up to 50% thicker than regular flighting throughout entire auger.
  • Tapered bearing gearbox.
  • Gearbox can be mounted for PTO on either side of auger.

T Series Auger Specifications

Auger Size T832 T836 T842 T852 T862 T1032 T1042 T1052 T1062 T1332 T11342
Auger length 30' 34' 42' 52' 62' 30' 42' 52' 62' 30' 42'
Lowered Reach 11'3" 14'6" 17'10" 21'3" 26'10" 10'8" 16'4" 21'3" 26'10" 12'1" 16'7"
Raised Reach 7'11" 8'8" 12'2" 12'2" 19'11" 7'4" 11'2" 12'2" 19'11" 8'10" 12'1"
Maximum Height ext. 18'7" 23'7" 24'10" 34'4" 39'3" 19'5" 25'7" 34'4" 39'3" 21'10" 24'4"
Transport Height 9'9" 12' 11'10" 14' 13' 9'9" 12'9" 14' 13' 7'10" 13'10"
Wheel transport width 74" 86" 86" 112" 125" 74" 86" 112" 125" 77" 86"
Tube Thickness 14ga 14ga 14ga 14ga 14ga 14ga 14ga 14ga 14ga 12ga 12ga
Flighting Thickness 1st 24" 7ga 7ga 7ga 7ga 7ga 5/16" 5/16" 5/16" 5/16" 5/16" 5/16"
Flighting Pitch 1st 24" 7" 7" 7" 7" 7" 9" 9" 9" 9" 12" 12"
Remainder Flighting Thickness 10ga 10ga 10ga 10ga 10ga 3/16" 3/16" 3/16" 3/16" 1/4" 1/4"
Flighting Pitch Remainder 7" 7" 7" 7" 7" 9" 9" 9" 9" 12" 12"
Entire auger flighting is Iron Edge Plus which is 50% thicker at the edge
Auger Flighting Core 1 1/2" 1 1/2" 1 1/2" 1 1/2" 1 1/2" 1.9" 1.9" 1.9" 1.9" 2-3/8" 2-3/8"
Gear Box Shaft Diameter 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8"
Drive Shaft Bearing Size 1" 1" 1" 1" 1" 1" 1" 1 1/4" 1 1/4" 1 1/4" 1 1/4"
Min. Horsepower (PTO) 7.5-10hp 10-15hp 10-15hp 15-20hp 20-25hp 7.5-10hp 10-15hp 15-17hp 15-20hp 45-50hp 60-65hp
Min. Horsepower (Electric) 5hp 5-7.5hp 5-7.5hp 7.5hp 10hp 2.5-5hp 5-7.5hp 7.5-10hp 10-12.5hp 20-25hp 30-35hp
Lift Mechanism cable cable cable cable cable cable cable cable cable cable cable
Frame Arms 2.5"x14ga 3"x14ga 3.5"x14ga 2.5"x14ga 3"x14ga 3.5"x11ga 3"x14ga 3.5"x11ga
Axle Tube Size 2 1/2"x2 1/2"x3/16" 3"x3"x3/16" 2 1/2"x2 1/2"x3/16" 3"x3"x3/16"
Tire Size 165/75x13 205/75x15 165/75x13 205/75x15
Capacity (Approx) 2800-4000bu/hr* 3500-5000bu/hr* 8800-9400bu/hr*
*Capacities will vary depending on commodities and other environmental factors.

T Series Auger Electric Motor Requirements

Auger Diameter (Inches) Recommended Auger Speed (RPM) Motor Size (HP) for Dry Corn Recommended Pulley Size (for 1750rpm motor) Motor Size (HP) for Wet Corn, Soybeans
T10x32 540 7.5 4.5” - 5” 10
T10x42 540 10 4.5” - 5” 15

T Series Auger Brochures

T Series BrochureT Series BrochureT Series Brochure